SIMEC

주메뉴 바로가기

본문 바로가기

푸터 바로가기

Introduction
Introduction

With Cutting-Edge Technology and Expertise,
SIMEC is Pioneering the Future
Business
Business

With Cutting-Edge Technology and Expertise,
SIMEC is Pioneering the Future
- CCV LINE
  EHV
  
  HV
  
  MV
  
  RUBBER-CV
- SUBMARINE MACHINE
  TURN TABLE
  
  CABLE ENGINE
- INSULATION / SHEATH LINE
  INSULATION LINE
  
  SHEATH LINE
Technological Capabilities
Technological Capabilities

With Cutting-Edge Technology and Expertise,
SIMEC is Pioneering the Future
- Smart CV 2.0
- RCP
- Roundness Control
- SAGCON
- Curve Design
- CAE
Support
Support

With Cutting-Edge Technology and Expertise,
SIMEC is Pioneering the Future

Pioneering the Future with Cutting-Edge Technology and Expertise, SIMEC

- Smart CV 2.0
- RCP
- Roundness Control
- SAGCON
- Curve Design
- CAE

CAE

Technological Capabilities

CAE
- Smart CV 2.0
- RCP
- Roundness Control
- SAGCON
- Curve Design
- CAE

HOME
Technological Capabilities
CAE

Technology

CAE

Application of Computer-Aided Extruder Design and Analysis

By leveraging computer-aided programs, we analyze material flow and temperature distribution during the extruder design phase. This approach enhances design efficiency,
lowers production costs, and improves overall performance and reliability.

CAE Tools

REX

Autodesk CFD

SOLIDWORKS Simulation

REX

Modeling of extrusion material output
Optimal screw design for temperature profile, L/D, and time.

Autodesk CFD

Improvement of crosshead extrusion quality
Verification of the effects of crosshead design modifications

SOLIDWORKS Simulation

Structural analysis of the frame
Stress calculation of key components

Privacy Policy
Do Not Collect Email
Site Map

SIMEC Inc.

735-11, Mado-ro, Mado-myeon, Hwaseong-si, Gyeonggi-do, 18541, Republic of Korea

Tel: +82-31-366-9691

Fax: +82-31-366-9694

Consent to Collection and Use of Personal Information
(SIMEC Co., Ltd.)

SIMEC Co., Ltd. (hereinafter referred to as the “Company” or “SIMEC”) collects the following personal information in order to operate the online inquiry service.

In accordance with the Act on Promotion of Information and Communications Network Utilization and Information Protection, your consent is required for the collection of personal information.

1. Purpose of Collection and Use of Personal Information
To identify and respond to inquiries, and to contact the individual regarding the inquiry.
The collected personal information will not be used for any purpose other than those specified. If the purpose of use changes, we will notify the individual and obtain additional consent.

2. Items of Personal Information Collected
Name, contact information, email address, and other minimum necessary information.
Consent is obtained prior to collecting this information.

3. Retention and Use Period of Personal Information
Personal information will be destroyed without delay once the purpose of collection and use has been fulfilled or the relevant service has been discontinued.
Specific retention periods are as follows:
For inquiries: Until the consultation is completed

4. Obligation to Notify Changes
If there are any additions, deletions, or modifications to this privacy policy, we will notify users at least 7 days in advance via a popup on the website.

Do Not Collect Email

1. We strictly prohibit the unauthorized collection of email addresses posted on this website using email harvesting programs or other technical methods. Please note that any violation may result in criminal penalties under the Information and Communications Network Act.

2. Article 50-2 of the Information and Communications Network Act (Prohibition on Unauthorized Collection of Email Addresses)
No person shall collect email addresses using programs or other technical devices from Internet websites where there is a clear notice refusing unauthorized collection of email addresses.

3. No person shall sell or distribute email addresses collected in violation of Paragraph 1.

4. No person shall use email addresses, which are prohibited from being collected, sold, or distributed under Paragraphs 1 and 2, for the purpose of transmitting information.